1. Data overview The data set of the base camp integrated environmental observation system is a set of ENVIS (IMKO, Germany) which was installed at the base camp observation point by qilian station.It is stored automatically by ENVIS data mining system. 2. Data content This data set is the scale data from January 1, 2011 to December 31, 2011.It mainly includes two layers of temperature, humidity and wind, six layers of soil water content, precipitation, 5cm geothermal flux, total radiation, seven layers of soil temperature, CO2 and air pressure. 3. Space and time scope Geographical coordinates: longitude: 99° 53’e;Latitude: 38°16 'N;Height: 2980.2 m
0 2020-03-10
All data in this data set are original data, including meteorological and soil moisture content, stem sap flow, water potential of plant tissue, isotope characteristics of atmospheric and humidified water vapor, fluorescence tracer image, plant photosynthetic fluorescence, and basic data of five desert plants, Tamarix chinensis, Haloxylon ammodendron, Bawang, Nitraria tangutorum and red sand, which are related to field and indoor control experiments Because of the data of expression regulation. 1. Isotopic data of Tamarix chinensis. After humidifying for 1 hour, 2 hours and 3 hours, the tissue samples of indoor and outdoor plants of plexiglass were collected at the same time. The samples were put forward and processed by low-temperature vacuum distillation glass water extraction system, and then used euro The isotopic data were measured by ea3000 element analyzer and isoprime gas stability mass spectrometer. Tamarix Tamarix samples were collected from Sitan village, Jingtai County, including humidification and control samples. The variation data of isotopic composition can be used to determine the way and amount of water vapor absorbed by plant leaves. 2. Fluorescence section photo data: all the data in this data set are original data, including the structural photos under high-power microscope of Tamarix, Haloxylon ammodendron, Nitraria, Bawang, Hongsha and other desert plant leaves in Sitan village of Jingtai County and Ejin Banner. The specific method is as follows: apply fluorescent dye to the surface of desert plant leaves before humidification, collect plant leaves and stems after humidification for 1 hour, 2 hours and 3 hours, put them in liquid nitrogen, take them back to the laboratory, observe and take photos with fluorescence microscope. It can be used to analyze the tissue and organs of water absorption by desert plant leaves and the direction and path of water migration in plants. 3: Gene transcription and expression data: transcription and expression data of Tamarix chinensis, data collection time: May 25, 2014, location: Sitan village, Jingtai County, Gansu Province, data analysis platform: lllumina hisep TM 2000 platform, obtained by transcriptome analysis of baimaike company. 4. Photosynthetic and fluorescence data: photosynthetic and fluorescence parameters measured by photosynthetic apparatus in the field (Sitan village and Ejin Banner, Jingtai County). 5. Sap flow and environmental data: all data are original data. Sap flow data of desert plants measured by stem flow meter, including Tamarix chinensis, Haloxylon ammodendron, Nitraria tangutorum, red sand and other desert plants (Sitan village, Jingtai County and Ejin Banner), and environmental data monitored by automatic weather station, including temperature and humidity.
0 2020-10-13
In the middle of August 2013, photosynthesis of population was measured, and plant species: red sand. The group photosynthesis measurement system consists of li-8100 closed-circuit soil carbon flux automatic measurement system (li-cor, USA) and assimilation box designed and manufactured by Beijing ligotai science and Technology Co., Ltd. li-8100 is an instrument produced by li-cor company of USA for soil carbon flux measurement. The concentration of CO2 and H2O is measured by infrared gas analyzer. The length, width and height of assimilation boxes were all 50 cm. The assimilator is controlled by li-8100. After the measurement parameters are set, the instrument can run automatically.
0 2020-03-12
I. Overview The Yellow River is the second longest river in our country. The problem of the Yellow River's sediment has attracted the attention of people all over the world. Based on the vector map of the 14 million rivers in China as a base map, the upper reaches of the Yellow River basin were cut out. The vector map of the river is a key element for extracting the boundary of the basin by using the topographic map, and it is also a key element for flood evolution and sediment evolution. Ⅱ. Data processing description Using the national vector map of the 14 million rivers as the data source, it is cut out by using the boundary of the upper reaches of the Yellow River. Ⅲ. Data content description The map is stored in ArcGIS, .shp files, including vector diagrams of the main and tributaries from the source area of the Yellow River to Toudaoguai. Ⅳ. Data usage description The vector map of the river is a key element for extracting the boundary of the watershed by using the topographic map, and it is also a key element for flood evolution and sediment evolution.
0 2020-06-01
This data is produced using knowledge rule-based land cover classification methods. It is a set of USGS global land cover classification standards that can be used in atmospheric models and land surface process models of land cover types in the Heihe River Basin. The data covers the upper, middle, and lower reaches of the Heihe River Basin. The data uses Albers Conical Equal Area projection with a spatial resolution of 1 km. It is an ASCII file containing the land cover classification code and named: Rule_Based_Lulc_of_HRB2009.asc. You can directly use a text program (such as Notepad) to open and view the file, you can also input it in ArcGIS for other operations. The NOAH land surface process parameter table and parameter table description matched with the data are provided. Users can refer to this parameter table to apply the data to the land surface process model. The two files are USGS_LULC_NOAHVEGPARM.TBL and NOAHVEGPARM_documentation.txt, both can be opened by the text program (such as Notepad).
0 2020-03-03
This dataset includes data recorded by the Heihe integrated observatory network obtained from the automatic weather station (AWS) at the Sidaoqiao mixed forest station from January 1 to December 31, 2018. The site (101.134° E, 41.990° N) was located on a tamarix and populous forest (Tamarix chinensis Lour. and Populus euphratica Olivier.) surface in the Sidaoqiao, Dalaihubu Town, Ejin Banner, Inner Mongolia Autonomous Region. The elevation is 874 m. The installation heights and orientations of different sensors and measured quantities were as follows: air temperature and humidity profile (28 m, north), wind speed and direction profile (28 m, north), air pressure (in tamper box), rain gauge (28 m, south), four-component radiometer (24 m, south), two infrared temperature sensors (24 m, south, vertically downward), two photosynthetically active radiation (24 m, south, one vertically upward and one vertically downward), soil heat flux (HFP01; 3 duplicates, -0.06 m), soil temperature profile (0, -0.02, -0.04, -0.1, -0.2, -0.4, -0.6, -1.0, -1.6, -2.0, -2.4 m), and soil moisture profile (-0.02, -0.04, -0.1, -0.2, -0.4, -0.6, -1.0, -1.6, -2.0, -2.4 m). The observations included the following: air temperature and humidity (Ta_28 m; RH_28 m) (℃ and %, respectively), wind speed (Ws_28 m) (m/s), wind direction (WD_28 m) (°), air pressure (press) (hpa), precipitation (rain) (mm), four-component radiation (DR, incoming shortwave radiation; UR, outgoing shortwave radiation; DLR_Cor, incoming longwave radiation; ULR_Cor, outgoing longwave radiation; Rn, net radiation) (W/m^2), infrared temperature (IRT_1 and IRT_2) (℃), photosynthetically active radiation of upward and downward (PAR_up and PAR_down) (μmol/ (s m^-2)), soil heat flux (Gs_1, Gs_2 and Gs_3) (W/m^2), soil temperature (Ts_0 cm, Ts_2 cm, Ts_4 cm, Ts_10 cm, Ts_20 cm, Ts_40 cm, Ts_60 cm, Ts_100, Ts_160, Ts_200, Ts_240 cm) (℃), and soil moisture (Ms_2 cm, Ms_4 cm, Ms_10 cm, Ms_20 cm, Ms_40 cm, Ms_60 cm, Ms_100, Ms_160, Ms_200, Ms_240 cm) (%, volumetric water content). The data processing and quality control steps were as follows: (1) The AWS data were averaged over intervals of 10 min for a total of 144 records per day. The missing data were denoted by -6999. Due to the power loss of datalogger, there were occasionally data missing during January 1 to 9, and November 10 to December 14; (2) Data in duplicate records were rejected. (3) Unphysical data were rejected. (4) The data marked in red are problematic data. (5) The format of the date and time was unified, and the date and time were collected in the same column, for example, date and time: 2018-9-10 10:30. (6) Finally, the naming convention was AWS+ site no. Moreover, suspicious data were marked in red. For more information, please refer to Liu et al. (2018) (for sites information), Liu et al. (2011) for data processing) in the Citation section.
0 2020-07-25
This data set contains meteorological element observation data from January 1, 2016 to December 31, 2016 at the downstream mixed forest station of heihe hydrometeorological observation network.The station is located at sidao bridge, dalaihubu town, ejin banner, Inner Mongolia.The longitude and latitude of the observation point are 101.1335e, 41.9903n and 874m above sea level.The air temperature and relative humidity sensors are located at 28m, facing due north.The barometer is installed in the anti-skid box on the ground;Tilting bucket rain gauge installed at 28m;The wind speed and direction sensor is located at 28m, facing due north.The four-component radiometer is installed at 24m, facing due south;Two infrared thermometers are installed at 24m, facing due south and the probe facing vertically downward.Two photosynthetically active radiators were installed at a position of 24m, facing due south, with one probe vertically upward and one probe vertically downward.The soil temperature probe is buried at 0cm of the surface and 2cm, 4cm, 10cm, 20cm, 40cm, 60cm and 100cm underground (observation at depths of 160cm,200cm and 240cm were increased on April 22), 2m to the south of the meteorological tower.The soil water probe was buried 2cm, 4cm, 10cm, 20cm, 40cm, 60cm and 100cm underground (observation at depths of 160cm,200cm and 240cm were increased on April 22), 2m to the south of the meteorological tower.The soil heat flow plates (3 pieces) are buried in the ground 6cm underground, 2m to the south of the meteorological tower. Observation items are: air temperature and humidity (Ta_28m, RH_28m) (unit: c, percentage), pressure (Press) (unit: hundred mpa), precipitation (Rain) (unit: mm), wind speed (WS_28m) (unit: m/s), wind (WD_28m) (unit: degrees), the radiation of four component (DR, UR, DLR_Cor, ULR_Cor, Rn) (unit: watts per square meter), the surface radiation temperature (IRT_1, IRT_2) (unit:C), soil heat flux (Gs_1, Gs_2, Gs_3) (in watts/m2), soil temperature (Ts_0cm, Ts_2cm, Ts_4cm, Ts_10cm, Ts_20cm, Ts_40cm, Ts_60cm, Ts_100cm, Ts_160cm, Ts_200cm, Ts_240cm) (in:C), soil moisture (Ms_2cm, Ms_4cm, Ms_10cm, Ms_20cm, Ms_40cm, Ms_60cm, Ms_100cm, Ms_160cm, Ms_200cm, Ms_240cm) (unit: volumetric water content, percentage), upward and downward photosynthetically active radiation (PAR_up, PAR_down) (unit: micromole/sq.s). Processing and quality control of observed data :(1) ensure 144 pieces of data every day (every 10min), and mark by -6999 in case of data missing;Due to the sensor problem, the wind direction was partly missing between April and April 21, 2016;The soil heat flux G1 is between 2.21-3.15, G2 is between 1.24-3.15, 4.4-4.22 and 12.1-12.21.(2) excluding the time with duplicate records;(3) data that obviously exceeds the physical significance or the range of the instrument is deleted;(4) the part marked with red letter in the data is the data in question;(5) date and time have the same format, and date and time are in the same column.For example, the time is: 2016-9-1010:30;(6) the naming rule is: AWS+ site name. For information of hydrometeorological network or station, please refer to Li et al. (2013), and for observation data processing, please refer to Liu et al. (2011).
0 2020-03-04
The data is the land cover data set of Tarim River Basin, which comes from "China's 1:100000 land use data set" in 2000. It is constructed based on LANDSAT MSS, TM and ETM Remote Sensing Data in three years by means of satellite remote sensing. Using a hierarchical land cover classification system, this data divides the whole country into six first-class categories (cultivated land, forest land, grassland, water area, urban and rural areas, industrial and mining land, residential land and unused land), and 31 second-class categories. The attribute fields are area, perimeter, code, and name.
0 2020-03-30
The data set is the contour map of the diving level in the middle reaches of heihe main stream, which contains the diving level profile of the middle reaches of heihe main stream in 2005, 2006 and 2007. It is made by arcgis as a vector map.Contains attributes such as length, elevation and thickness of equal water level line.Its scope is: Left: 604028.6599 right: 645635.1531 Above: 4333504.1090 below: 4296403.637
0 2020-03-08
11 groundwater level observation logs are arranged in the transition zone from Heihe River to desert oasis in Pingchuan oasis, Linze. From May to July 2012-2013, the groundwater level is monitored three times a month, and the NO3-N content, Cl, SO42 - change are analyzed by sampling once a month.
0 2020-07-30
Contact Support
Northwest Institute of Eco-Environment and Resources, CAS
0931-4967287
poles@itpcas.ac.cn
Links
National Tibetan Plateau Data CenterFollow Us
A Big Earth Data Platform for Three Poles © 2018-2020 No.05000491 | All Rights Reserved
｜ 
No.11010502040845
Tech Support: westdc.cn
