This dataset contains the flux measurements from the Huailai station eddy covariance system (EC) from April 13 to December 31 in 2021. The site (115.7923° E, 40.3574° N) was located in the maize surface, near Donghuayuan town of Huailai city in Hebei Province. The elevation is 480 m. The EC was installed at a height of 3.5 m, and the sampling rate was 10 Hz. The sonic anemometer faced north, and the separation distance between the sonic anemometer and the CO2/H2O gas analyzer (CSAT3&EC150) was 0 m. The raw data acquired at 10 Hz were processed using the Eddypro post-processing software, including the spike detection, lag correction of H2O/CO2 relative to the vertical wind component, sonic virtual temperature correction, coordinate rotation (2-D rotation), corrections for density fluctuation (Webb-Pearman-Leuning correction), and frequency response correction. The EC data were subsequently averaged over 30 min periods. The observation data quality was divided into three classes according to the quality assessment method of stationarity (Δst) and the integral turbulent characteristics test (ITC) (class1-9). In addition to the above processing steps, the half-hourly flux data were screened in a four-step procedure: (1) data from periods of sensor malfunction were rejected; (2) data collected before or after 1 h of precipitation were rejected; (3) incomplete 30 min data were rejected when the missing data constituted more than 10% of the 30 min raw record; and (4) data were rejected at night when the friction velocity (u*) was less than 0.1 m/s. There were 48 records per day, and the missing data were replaced with -6999. Suspicious data were marked in red. There were lots of negative values of H2O density in winter where filling by -6999. The released data contained the following variables: data/time, wind direction (Wdir, °), wind speed (Wnd, m/s), the standard deviation of the lateral wind (Std_Uy, m/s), virtual temperature (Tv, ℃), H2O mass density (H2O, g/m3), CO2 mass density (CO2, mg/m3), friction velocity (ustar, m/s), stability (z/L), sensible heat flux (Hs, W/m2), latent heat flux (LE, W/m2), carbon dioxide flux (Fc, mg/ (m2s)), quality assessment of the sensible heat flux (QA_Hs), quality assessment of the latent heat flux (QA_LE), and quality assessment of the carbon flux (QA_Fc). In this dataset, the time of 0:30 corresponds to the average data for the period between 0:00 and 0:30; the data were stored in *.xls format. Detailed information can be found in the suggested references. For more information, please refer to Guo et al. (2020) (for sites information), Liu et al. (2013) for data processing) in the Citation section.
LIU Shaomin, XIAO Qing, XU Ziwei, BAI Junhua
This dataset contains the flux measurements from the large aperture scintillometer (LAS) at Huailai station. There were two types of LASs: German BLS450 and zzLAS. The observation periods were from January 1 to December 31, 2021. The site ( (north: 115.7825° E, 40.3522° N; south: 115.7880° E, 40.3491° N) was located in the Donghuahuan town of Huailai city, Hebei Province. The elevation is 480 m. The underlying surface between the two towers contains mainly maize. The effective height of the LASs was 14 m; the path length was 1870 m. Data were sampled at 1 min intervals. Raw data acquired at 1 min intervals were processed and quality-controlled. The data were subsequently averaged over 30 min periods. The main quality control steps were as follows. (1) The data were rejected when Cn2 was beyond the saturated criterion. (2) Data were rejected when the demodulation signal was small. (3) Data were rejected within 1 h of precipitation. (4) Data were rejected at night when weak turbulence occurred (u* was less than 0.1 m/s). The sensible heat flux was iteratively calculated by combining with meteorological data and based on Monin-Obukhov similarity theory. There were several instructions for the released data. (1) The data were primarily obtained from BLS450 measurements; missing flux measurements from the BLS450 were filled with measurements from the zzLAS. Missing data were denoted by -6999. (2) The dataset contained the following variables: data/time (yyyy-mm-dd hh:mm:ss), the structural parameter of the air refractive index (Cn2, m-2/3), and the sensible heat flux (H_LAS, W/m^2). (3) In this dataset, the time of 0:30 corresponds to the average data for the period between 0:00 and 0:30; the data were stored in *.xls format. Moreover, suspicious data were marked in red. For more information, please refer to Guo et al. (2020) (for sites information), Liu et al. (2013) (for data processing) in the Citation section.
LIU Shaomin, XU Ziwei
This dataset obtained from an observation system of Meteorological elements gradient of Huailai station from January 1 to December 31, 2021. The site (115.7923° E, 40.3574° N) was located on a cropland (maize surface) which is near Donghuayuan town of Huailai city, Hebei Province. The elevation is 480 m. The installation heights and orientations of different sensors and measured quantities were as follows: air temperature and humidity profile (3, 5, 10, 15, 20, 30, and 40 m, towards north), wind speed and direction profile (3, 5, 10, 15, 20, 30, and 40 m, towards north), air pressure (in the box), rain gauge (3 m, south of tower), four-component radiometer (4 m, south of tower), two infrared temperature sensors (4 m, south of tower, vertically downward), photosynthetically active radiation (4 m, south of tower, vertically upward), soil heat flux -0.06 m), a TCAV averaging soil thermocouple probe (-0.02, -0.04 m), soil temperature profile (-0.02, -0.04, -0.1, -0.2, -0.4, -0.8, -1.2, and -1.6 m), soil moisture profile (-0.02, -0.04, -0.1, -0.2, -0.4, -0.8, -1.2, and -1.6 m). The observations included the following: air temperature and humidity (Ta_3 m, Ta_10 m, Ta_15 m, Ta_20 m, Ta_30 m, and Ta_40 m; RH_3 m, RH_5 m, RH_10 m, RH_15 m, RH_20 m, RH_30 m, and RH_40 m) (℃ and %, respectively), wind speed (Ws_3 m, Ws_10 m, Ws_15 m, Ws_20 m, Ws_30 m) (m/s), wind direction (WD_10 m) (°), air pressure (press) (hpa), precipitation (rain) (mm), four-component radiation (DR, incoming shortwave radiation; UR, outgoing shortwave radiation; DLR_Cor, incoming longwave radiation; ULR_Cor, outgoing longwave radiation; Rn, net radiation) (W/m^2), infrared temperature (IRT_1 and IRT_2) (℃), photosynthetically active radiation (PAR) (μmol/ (s m-2)), average soil temperature (TCAV, ℃), soil heat flux (Gs) (W/m^2), soil temperature (Ts_2 cm, Ts_4 cm, Ts_10 cm, Ts_20 cm, Ts_40 cm, Ts_80 cm, Ts_120 cm, and Ts_160 cm) (℃), soil moisture (Ms_2 cm, Ms_4 cm, Ms_10 cm, Ms_20 cm, Ms_40 cm, Ms_80 cm, Ms_120 cm, and Ms_160 cm) (%, volumetric water content). The data processing and quality control steps were as follows: (1) The AWS data were averaged over intervals of 10 min for a total of 144 records per day. The missing data were denoted by -6999. (2) Data in duplicate records were rejected. (3) Unphysical data were rejected. (4) The data marked in red are problematic data. (5) The format of the date and time was unified, and the date and time were collected in the same column, for example, date and time: 2021-6-10 10:30. Moreover, suspicious data were marked in red. For more information, please refer to Guo et al. (2020) (for sites information), Liu et al. (2013) for data processing) in the Citation section.
LIU Shaomin, XIAO Qing, XU Ziwei, BAI Junhua
This dataset includes data obtained from the automatic weather station (AWS) at the observation system of Meteorological elements of Huailai station between January 1 and December 31, 2021. The site (115.7880° E, 40.3491° N) was located on a maize surface, which is near Donghuayuan Town of Huailai city in Hebei Province. The elevation is 480 m. The installation heights and orientations of different sensors and measured quantities were as follows: air temperature and humidity profile (5 m, north), wind speed and direction profile (10 m, north), air pressure (in the box), rain gauge (10 m), four-component radiometer (5 m, south), two infrared temperature sensors (5 m, south, vertically downward), soil heat flux (-0.06 m), soil temperature profile (0, -0.02, -0.04, -0.1, -0.2, -0.4, -0.8, -1.2, and -1.6 m), soil moisture profile (-0.02, -0.04, -0.1, -0.2, -0.4, -0.8, -1.2, and -1.6 m), and a TCAV averaging soil thermocouple probe (-0.02, -0.04 m). The observations included the following: air temperature and humidity (Ta_5 m; RH_5 m) (℃ and %, respectively), wind speed (Ws_10 m) (m/s), wind direction (WD_10 m) (°), air pressure (press) (hpa), precipitation (rain) (mm), four-component radiation (DR, incoming shortwave radiation; UR, outgoing shortwave radiation; DLR_Cor, incoming longwave radiation; ULR_Cor, outgoing longwave radiation; Rn, net radiation) (W/m2), infrared temperature (IRT_1 and IRT_2) (℃), soil heat flux (Gs_1, Gs_2 and Gs_3) (W/m2), soil temperature (Ts_0 cm, Ts_2 cm, Ts_4 cm, Ts_10 cm, Ts_20 cm, Ts_40 cm, Ts_80 cm, Ts_120 cm, and Ts_160 cm) (℃), soil moisture (Ms_2 cm, Ms_4 cm, Ms_10 cm, Ms_20 cm, Ms_40 cm, Ms_80 cm, Ms_120 cm, and Ms_160 cm) (%, volumetric water content), and average soil temperature (TCAV, ℃). The data processing and quality control steps were as follows: (1) The AWS data were averaged over intervals of 10 min for a total of 144 records per day. The missing data were denoted by -6999. (2) Data in duplicate records were rejected. (3) Unphysical data were rejected. (4) The data marked in red are problematic data. (5) The format of the date and time was unified, and the date and time were collected in the same column, for example, date and time: 2021-6-10 10:30. (6) Finally, the naming convention was AWS+ site no. Moreover, suspicious data were marked in red. For more information, please refer to Guo et al. (2020) (for sites information), Liu et al. (2013) (for data processing) in the Citation section.
LIU Shaomin, XU Ziwei
This dataset contains the flux measurements from the Huailai station eddy covariance system (EC) from January 1 to December 31 in 2021. The site (115.7880° E, 40.3491°N) was located in the maize surface, near Donghuayuan town of Huailai city in Hebei Province. The elevation is 480 m. The EC was installed at a height of 5 m, and the sampling rate was 10 Hz. The sonic anemometer faced north, and the separation distance between the sonic anemometer and the CO2/H2O gas analyzer (CSAT3&Li7500A) was 0.15 m. The raw data acquired at 10 Hz were processed using the Eddypro post-processing software, including the spike detection, lag correction of H2O/CO2 relative to the vertical wind component, sonic virtual temperature correction, coordinate rotation (2-D rotation), corrections for density fluctuation (Webb-Pearman-Leuning correction), and frequency response correction. The EC data were subsequently averaged over 30 min periods. The observation data quality was divided into three classes according to the quality assessment method of stationarity (Δst) and the integral turbulent characteristics test (ITC) (class 1 to 9). In addition to the above processing steps, the half-hourly flux data were screened in a four-step procedure: (1) data from periods of sensor malfunction were rejected; (2) data collected before or after 1 h of precipitation were rejected; (3) incomplete 30 min data were rejected when the missing data constituted more than 10% of the 30 min raw record; and (4) data were rejected at night when the friction velocity (u*) was less than 0.1 m/s. There were 48 records per day, and the missing data were replaced with -6999. The released data contained the following variables: data/time, wind direction (Wdir, °), wind speed (Wnd, m/s), the standard deviation of the lateral wind (Std_Uy, m/s), virtual temperature (Tv, ℃), H2O mass density (H2O, g/m3), CO2 mass density (CO2, mg/m3), friction velocity (ustar, m/s), stability (L), sensible heat flux (Hs, W/m2), latent heat flux (LE, W/m2), carbon dioxide flux (Fc, mg/ (m2s)), quality assessment of the sensible heat flux (QA_Hs), quality assessment of the latent heat flux (QA_LE), and quality assessment of the carbon flux (QA_Fc). In this dataset, the time of 0:30 corresponds to the average data for the period between 0:00 and 0:30; the data were stored in *.xls format. Detailed information can be found in the suggested references. For more information, please refer to Guo et al. (2020) (for sites information), Liu et al. (2013) for data processing) in the Citation section.
LIU Shaomin, XU Ziwei
1) Data content This data set includes lake evaporation data of Bamco, La'angco in the summer and autumn of 2019-2021 and Longmuco in the summer and autumn of 2020-2021. The meteorological data required for the calculation of evaporation data are obtained from the automatic meteorological station set up at the lake side, with the observation height of 1.5m. Lake location: Bamco (90.59 ° E, 31.29 ° N), La'anco (81.24 ° E, 30.72 ° N), Longmucuo (80.47 ° E, 34.60 ° N). Coordinates of automatic weather stations: Bamco AWS (90.65 ° E, 31.30 ° N), La'anco AWS (81.22 ° E, 30.73 ° N), and Longmucuo AWS (80.43 ° E, 34.59 ° N). Time resolution: 1d Spatial resolution:- Unit: mm 2) Data source and processing method Integral conveying method. The calculation formula is as follows: LH=l_ v ρ_ a c_ E U(q_s-q_a ) E=LH/( ρ l_ v ) LH and E are latent heat and evaporation respectively. The automatic weather station erected near the lake is used for meteorological data, and the observation data used include temperature, wind speed, relative humidity, etc. at 1.5m; Lake surface temperature uses ERA5 land hourly data; The momentum roughness, moisture roughness and thermal roughness are obtained by back calculation from the data obtained by the eddy correlation instrument erected by Bamco and Laoncho. 3) Data quality description The evaporation data of Bamco Lake in 2020 obtained by calculation are compared with the evaporation data from August to October obtained by the eddy correlation instrument installed on the central island of Bamco Lake. Pearson correlation coefficient r=0.57, p=2.842E-8. 4) Data application achievements and prospects Water surface evaporation is an important link in the process of water cycle and an important topic in hydrology research. As the main part of lake water loss, it is also the basic reference data for studying land surface evaporation. The evaporation calculated based on the observation data can be used as the accurate evaporation of lakes on the Qinghai Tibet Plateau, which is an important basis for studying the water balance of lakes. By obtaining the evaporation of three lakes located in different climatic regions, we can better explore the variation law of lake water surface evaporation in different climatic regions.
MA Weiyao , MA Weiqiang*, HE Jianan , XIE Zhipeng , SU Rongmingzhu , HU Wei , MA Yaoming
The global reach-level 3-hourly river flood reanalysis (GRFR) dataset includes 1) global 0.05 degree, 3-hourly/daily runoff data, 2) 3hourly/daily naturalized river discharge at 2.94 million river reaches, 3) global 3-hourly river flood events from 1980 to 2019, 4) underlying hydrography MERIT-Basins. Grounded on recent breakthroughs in global runoff hydrology, river modeling, high-resolution hydrography, and climate reanalysis, the 3-hourly river discharge record globally for 2.94 million river reaches during the 40-yr period of 1980–2019 was developed. The underlying modeling chain consists of the VIC land surface model (0.05°, 3-hourly) that is well calibrated and bias-corrected and the RAPID routing model (2.94 million river and catchment vectors), with precipitation input from MSWEP and other meteorological fields downscaled from ERA5. Flood events (above 2-yr return) and their characteristics (number, spatial distribution, and seasonality) were extracted and studied. Validations against 3-hourly flow records from 6,000+ gauges in CONUS and daily records from 14,000+ gauges globally show good modeling performance across all flow ranges, good skills in reconstructing flood events (high extremes), and the benefit of (and need for) sub-daily modeling. The GRFR database represents a pioneering effort on global reach-level flood reanalysis and may offer new opportunities for global flood studies in terms of baseline data and potential research pathways. Also, it can better help river-observing satellite missions to develop their discharge algorithms.
YANG Yuan , PAN Ming , LIN Peirong
Natural runoff simulation data products of 2.94 million river sections in the world, unit: m3/s. This data is based on the simulation of VIC hydrological process model and RAPID vector river network concentration model. The spatial resolution of the land surface hydrological process model is 0.25 °, and the river network data in the vector concentration model is extracted based on the 90-m MERIT Hydro hydrological correction terrain data product. The runoff generation part is calibrated based on the runoff characteristic values obtained by machine learning, and the grid scale runoff generation deviation correction is carried out based on the multi quantile runoff characteristic values. The data products are verified by 14000 runoff observation stations around the world, and have better verification accuracy.
LIN Peirong , PAN Ming , YANG Yuan
This data is generated based on meteorological observation data, hydrological station data, combined with various assimilation data and remote sensing data, through the preparation of the Qinghai Tibet Plateau multi-level hydrological model system WEB-DHM (distributed hydrological model based on water and energy balance) coupling snow, glacier and frozen soil physical processes. The time resolution is monthly, the spatial resolution is 5km, and the original data format is ASCII text format, Data types include grid runoff and evaporation (if evaporation is less than 0, it means condensation; if runoff is less than 0, it means precipitation is less than evaporation in the month). If the asc cannot be opened normally in arcmap, please top the first 5 lines of the asc file.
WANG Lei, CHAI Chenhao
This data is a 5km monthly hydrological data set, including grid runoff and evaporation (if evaporation is less than 0, it means condensation; if runoff is less than 0, it means precipitation is less than evaporation), simulated and output through the WEB-DHM distributed hydrological model of the Indus River basin, with temperature, precipitation, barometric pressure, etc. as input data.
WANG Lei, LIU Hu
Water is one of the most direct mediums through which people perceive the effects of climate change. The flow regimes that people rely on are influenced by large-scale climate change, and identifying changes to these regimes and determining their causes requires reliable, spatiotemporally continuous runoff records. China is climate vulnerable due to its remarkable topographic gradients, monsoon climate, and rapid economic development. Climate change has increased the urgency of understanding, regulating, and forecasting China’s freshwater flows. Yet, available global and regional runoff data in China are produced from sparse, poor-quality gauged station data that have been acquired over different time scales. Our research presents a new long-term, high-quality natural runoff dataset, named the China Natural Runoff Dataset version 1.0 (CNRD v1.0) for driving hydrological and climate studies over China. It will also contribute to the global runoff database. CNRD v1.0 provides daily, monthly, and annual 0.25-degree natural runoff estimates for the period of 1 January 1961 to 31 December 2018 over China. CNRD v1.0 is generated using the Variable Infiltration Capacity macroscale hydrological model, which was used to fill in gaps or construct time series of comparable lengths. To control the model performance and thus our dataset quality, the model’s sensitive parameters are automatically calibrated using an adaptive surrogate modeling‐based optimization algorithm based on monthly natural or near-natural streamflow data from 200 hydrological gauge stations—more than in previous studies—with low fractions of missing data. Another important quality control adopted for this dataset was the use of a multiscale parameter regionalization technique to estimate model parameters for ungauged basins. Overall, the results show well-calibrated parameters for most gauged catchments, and the skill scores, the Nash–Sutcliffe model efficiency coefficient (NSE) present high values for all catchments, with an average of 0.83 and 0.80 for calibration and validation modes, respectively. The multiscale parameter regionalization technique offered the best regionalization solution (median NSE = 0.76 for the calibration period and 0.72 for the validation period. The results overall show well-calibrated and regionalized parameters for the hydrological model thus for the long-term runoff reconstruction. By the cell-to-cell comparisons between the CNRD v1.0 with the two global runoff datasets, ISIMIP and GRUN, we found that our datasets show more continuous transitions in runoff dis¬tribution compared to ISIMIP and GRUN across China, and perform well in representing the geographic distribution of China’s water resources across complex terrain and climate regions.
MIAO Chiyuan, GOU Jiaojiao
This data set is a global surface evapotranspiration product based on the PEW model. The PEW model is a water energy based surface energy balance model based on the assumption of equal proportion. Its principle is to couple the water heat balance framework based on the assumption of equal proportion on the Priestley Taylor (PT) evapotranspiration algorithm. PEW model can consider the influence of water balance constraint and energy budget process at the same time, which makes the simulation accuracy of PEW model improved compared with previous models to a certain extent. The input data of PEW include the meteorological and soil moisture changes of ERA5 land dataset. The time span of this dataset is from 1982 to 2018. The time resolution is month by month and the spatial resolution is 0.1 °. This data set can provide a basis for studying the long-term water cycle and climate change.
FU Jianyu , WANG Weiguang
This data set is the data set of water balance (precipitation, evapotranspiration, runoff, liquid soil moisture) and energy balance (short wave radiation, sensible heat, latent heat and surface soil temperature) for the source of the Yellow River and the Qilian Mountains over the past 40 years. The initial data source is ERA5 Land monthly average data, which is accumulated/averaged to the annual scale through time aggregation. The time range of the data is 1981-2020, the spatial range is 88.5 ° E – 104.5 ° E, 32 ° N – 43 ° N, and the spatial resolution is 0.1 °. The data set can be further used to study the ecological hydrological processes in the source area of the Yellow River and the Qilian Mountains, and provide scientific basis for the optimal allocation of the "mountains, rivers, forests, fields, lakes and grasses" system.
ZHENG Donghai
In the context of global change, the spatio-temporal continuous high-quality high-resolution long time series precipitation data set is of great significance for understanding the global "water carbon energy" and biogeochemical cycle mechanism. The daily total volume controlled merging and disaggregation algorithm (DTVCMDA) proposed in this study effectively considers the characteristics of continuous space-time and high spatial and temporal resolution of reanalysed precipitation data, as well as the high quality of ground analysis data, A set of AERA5 Asia (0.1 °, hourly, 1951-2015, Asia) precipitation data set with high quality and high spatial and temporal resolution for more than 70 years of long time series in Asia has been produced. The main features of the dataset are as follows: (1) AERA5 Asia is a set of data sets with high resolution, high quality, space-time continuity and long time series; (2) AERA5 Asia is significantly better than IMERG Final and ERA5 Land precipitation data, especially in terms of system deviation. In general, the deviation of AERA5 Asia, IMERG Final and ERA5 Land compared with ground observation is~5%,~11% and~20% respectively; (3) In extreme heavy rainfall (such as typhoons "Tamei" and "Tiantu"), the quality of AERA5 Asia is also significantly better than ERA5 Land and IMERG Final. AERA5 Asia will provide stable and reliable precipitation data support for relevant research in the weather, climate, hydrology and other fields in Asia, especially in China.
MA Ziqiang, MA Yaoming, MA Weiqiang*, 许金涛 XU Jintao
Terrestrial actual evapotranspiration (ET) is an essential ecohydrological process linking the land surface energy, water and carbon cycles, and plays a critical role in the earth system. This global ET dataset is obtained based on ETMonitor model, which combines parameterizations for different processes and land cover types, with multi-source satellite data as input. Several open accessed remote sensing variables, e.g., LAI, FVC, albedo, surface soil moisture, dynamic surface water cover and snow/ice cover, were used as input to estimate daily ET. The meteorological variables from ERA5 reanalysis dataset were also adopted. The ETMonitor model is applied at daily scale to estimate the ET components at 1-km resolution, including vegetation transpiration, soil evaporation, canopy precipitation interception loss, water surface evaporation and snow/ice sublimation on daily step, and the total actual ET is estimated as the sum of these components. Overall, the actual ET estimated by ETMonitor agreed well with ground measurements from 251 flux towers across various ecosystems and climate zones globally, with high correlation (0.75), low bias (0.08mm/d), and low root mean square error (0.93 mm/d). The estimated ET showed reasonable spatial patterns, and superior in presenting the spatial variation of ET especially in the mountain regions and in the arid irrigated cropland regions. The ET estimation is conducted at daily temporal step and 1km spatial resolution. For easier publication, the daily/1-km ET from ETMonitor (https://doi.org//10.12237/casearth.6253cddc819aec49731a4bc2) was summed to obtain monthly ET in this dataset. The data type is 16-bit signed integer, the scale factor is 0.1, and the unit is mm/month. The missing values were filled by -1.
ZHENG Chaolei , JIA Li , HU Guangcheng
Based on the Sentinel-2 and Landsat 5/7/8 multispectral instrument imageries combined with in-situ measured hydrological data, bankfull river geometry of six major exorheic river basins of the Qinghai-Tibet Plateau (the upper Yellow River, upper Jinsha River, Yalong River, Lantsang River, Nu River and Yalung Zangbo River) are presented. River surface of six mainstreams and major tributaries are included. For each river basin, two types of rivers are included: connected and disconnected rivers. Format of the dataset is .shp exported from the ArcGIS 10.5. Three products are included in the dataset: one original product (bankfull river surface dataset) and two derived products (bankfull river width dataset and bankfull river surface area dataset with a 1 km river length interval). These three products are in three folders. The first folder, “1-Bankfull River Surface”, contains river surface vectors for six river basins in the .shp file. The second folder, “2-Bankfull River Width”, contains bankfull river widths and corresponding coordinates with a 1 km-step river length for six mainstreams and some connected tributaries in .xlsx format. The river width vectors in the .shp files are also provided in the second folder. The third folder, “3-Bankfull River Surface Area”, contains bankfull river surface areas and corresponding coordinates with a 1 km-step river length for six mainstreams and some connected tributaries in .xlsx format. Three Supplementary Files are included: Supplementary File 1, tables and figures related to the dataset; Supplementary File 2, used for river surface extraction based on GEE platform; Supplementary File 3, used for river width extraction based on Matlab. The provided planform river hydromorphology data can supplement global hydrography datasets and effectively represent the combined fluvial geomorphology and geological background in the study area.
LI Dan , XUE Yuan , QIN Chao , WU Baosheng , CHEN Bowei , WANG Ge
The water resources simulation data of Southeast Asian countries and the Lancang Mekong River Basin (1980-2019) is the result of using the meteorological data output from the WRF model as the driving data and simulation through the ways model. The data includes evapotranspiration, surface runoff, underground runoff, total runoff, groundwater, infiltration and soil moisture data of Southeast Asia land area from 1980 to 2019. The temporal resolution is daily and the spatial resolution is 3km. The data is generally good, but due to the limitations of the model, there are certain errors in the simulation results of a few variables. It is not recommended to use the research with high requirements for data accuracy. The data can reflect the situation of water resources in Southeast Asia to a certain extent, and provide data support for relevant research.
LIU Junguo
The basic data of hydrometeorology, land use and DEM were collected through the National Meteorological Information Center, the hydrological Yearbook, the China Statistical Yearbook and the Institute of geographical science and resources of the Chinese Academy of Sciences. The distributed time-varying gain hydrological model (DTVGM) with independent intellectual property rights is adopted for modeling, and the Qinghai Tibet Plateau is divided into 10937 sub basins with a threshold of 100 square kilometers. The daily flow data of 14 flow stations in Heihe River, Yarlung Zangbo River, Yangtze River source, Yellow River source, Yalong River, Minjiang River and Lancang River Basin were selected to draft and verify the model. The daily scale Naxi efficiency coefficient is above 0.7 and the correlation coefficient is above 0.8. The actual evaporation simulation is basically consistent with the station observation published by the Meteorological Bureau. The model simulates the water cycle process from 1998 to 2017. After verification, the spatial and temporal distribution of the actual evaporation (including soil evaporation and plant transpiration) on the 0.01 degree daily scale in the whole Tibetan Plateau is given.
YE Aizhong
The basic data of hydrometeorology, land use and DEM were collected through the National Meteorological Information Center, the hydrological Yearbook, the China Statistical Yearbook and the Institute of geographical science and resources of the Chinese Academy of Sciences. The distributed time-varying gain hydrological model (DTVGM) with independent intellectual property rights is adopted for modeling, and the Qinghai Tibet Plateau is divided into 10937 sub basins with a threshold of 100 square kilometers. The daily flow data of 14 flow stations in Heihe River, Yarlung Zangbo River, Yangtze River source, Yellow River source, Yalong River, Minjiang River and Lancang River Basin were selected to draft and verify the model. The daily scale Naxi efficiency coefficient is above 0.7 and the correlation coefficient is above 0.8. The model simulates the water cycle process from 1998 to 2017, and gives the spatial and temporal distribution of 0.01 degree daily scale runoff in the whole Qinghai Tibet Plateau.
YE Aizhong
The data set of bacterial post-treatment products and conventional water quality parameters of some lakes in the third pole in 2015 collected the bacterial analysis results and conventional water quality parameters of some lakes in the Qinghai Tibet Plateau during 2015. Through sorting, summarizing and summarizing, the bacterial post-treatment products of some lakes in the third pole in 2015 are obtained. The data format is excel, which is convenient for users to view. The samples were collected by Mr. Ji mukan from July 1 to July 15, 2015, including 28 Lakes (bamuco, baimanamuco, bangoso (Salt Lake), Bangong Cuo, bengcuo, bieruozhao, cuo'e (Shenza), cuo'e (Naqu), dawaco, dangqiong Cuo, dangjayong Cuo, Dongcuo, eyaco, gongzhucuo, guogencuo, jiarehbu Cuo, mabongyong Cuo, Namuco, Nier CuO (Salt Lake), Norma Cuo, Peng yancuo (Salt Lake), Peng Cuo, gun Yong Cuo, Se lincuo, Wu rucuo, Wu Ma Cuo, Zha RI Nan Mu Cuo, Zha Xi CuO), a total of 138 samples. The extraction method of bacterial DNA in lake water is as follows: the lake water is filtered onto a 0.45 membrane, and then DNA is extracted by Mo bio powerOil DNA kit. The 16S rRNA gene fragment amplification primers were 515f (5'-gtgccagcmgcgcggtaa-3') and 909r (5'-ggactachvggtwtctaat-3'). The sequencing method was Illumina miseq PE250. The original data were analyzed by mothur software, including quality filtering and chimera removal. The sequence classification was based on the silva109 database. The archaeal, eukaryotic and unknown source sequences had been removed. OTU classifies with 97% similarity and then removes sequences that appear only once in the database. Conventional water quality detection parameters include dissolved oxygen, conductivity, total dissolved solids, salinity, redox potential, nonvolatile organic carbon, total nitrogen, etc. The dissolved oxygen is determined by electrode polarography; Conductivity meter is used for conductivity; Salinity is measured by a salinity meter; TDS tester is used for total dissolved solids; ORP online analyzer was used for redox potential; TOC analyzer is used for non-volatile organic carbon; The water quality parameters of total nitrogen were obtained by Spectrophotometry for reference.
YE Aizhong
The data set includes the observed and simulated runoff into the sea and the composition of each runoff component (total runoff, glacier runoff, snowmelt runoff, rainfall runoff) of two large rivers in the Arctic (North America: Mackenzie, Eurasia: Lena), with a time resolution of months. The data is a vic-cas model driven by the meteorological driving field data produced by the project team. The observed runoff and remote sensing snow data are used for correction. The Nash efficiency coefficient of runoff simulation is more than 0.85, and the model can also better simulate the spatial distribution and intra/inter annual changes of snow cover. The data can be used to analyze the runoff compositions and causes of long-term runoff change, and deepen the understanding of the runoff changes of Arctic rivers.
ZHAO Qiudong, WU Yuwei
This product provides the data set of key variables of the water cycle of major Arctic rivers (North America: Mackenzie, Eurasia: Lena from 1971 to 2017, including 7 variables: precipitation, evapotranspiration, surface runoff, underground runoff, glacier runoff, snow water equivalent and three-layer soil humidity, which are numerically simulated by the land surface model vic-cas developed by the project team. The spatial resolution of the data set is 0.1degree and the temporal resolution is month. This data set can be used to analyze the change of water balance in the Arctic River Basin under long-term climate change, and can also be used to compare and verify remote sensing data products and the simulation results of other models.
ZHAO Qiudong, WANG Ninglian, WU Yuwei
This product provides the data set of key variables of the water cycle of Arctic rivers (North America：Mackenzie, Eurasia：Lena) from 1998 to 2017, including 7 variables: precipitation, evapotranspiration, surface runoff, underground runoff, glacier runoff, snow water equivalent and three-layer soil humidity, which are numerically simulated by the land surface model vic-cas developed by the project team. The spatial resolution of the data set is 50km and the temporal resolution is month. This data set can be used to analyze the change of water balance in the Arctic River Basin under climate change, and can also be used to compare and verify remote sensing data products and the simulations of other models.
ZHAO Qiudong, WANG Ninglian, WU Yuwei
This dataset contains the monthly evaporation rate and volumes for 7242 reservoirs from March 1984 to December 2016 across the world. The evaporation rate was calculated using the three datasets viz. (1) TerraClimate; (2) ERA5; (3) Princeton Global Forcings. The surface area of these reservoirs is obtained from the Global reservoir surface area dataset (GRSAD). The detailed descriptions for this dataset are presented in Tian et al (2021,2022). The basic information of the global reservoirs was provided by the Global Reservoir and Dam Database (GRanD).
TIAN Wei , LIU Xiaomang, WANG Kaiwen , BAI Peng , LIU Changming
This product provides the monthly runoff, evapotranspiration and soil water of major Arctic river basins in 2018-2065 based on the land surface model Vic. The spatial accuracy is 10km. Major Arctic river basins include Lena, Yenisey, ob, Kolyma, Yukon and Mackenzie basins. According to the rcp2.6 (low emission intensity) and rcp8.5 (high emission intensity) scenario results provided by the ipsl-cm5a-lr model in cmip5 in the fifth assessment report of IPCC, the future climate scenario driving data applicable to the Arctic region of 0.1 ° is obtained through statistical downscaling. Using the calibrated land surface hydrological model Vic on a global scale, based on the future climate scenario driven data of 0.1 °, the monthly time series of runoff, soil water and evapotranspiration of the Arctic River Basin in the middle of this century under future climate change are estimated.
TANG Yin , TANG Qiuhong , WANG Ninglian, WU Yuwei
This dataset provide the daily observations of soil water contents and soil temperature in the Qihuli catchment in the upper reach of Qihai Lake basin. Daily soil water content and soil temperature were measured in the shady slope, sunny slope and the outfall of this catchment in the period of 2019-2021. The Qihuli catchment is located at 37°25′N and 100°15′E, with the elevation ranging from 3565-3716. The soil water content and soil temperature were continuously monitored using the ECH2O and 5TE sensors at both shady and sunny slopes. The monitoring depths are 10 cm, 30 cm, 50 cm, 80 cm, 110 cm, and 10 cm, 30 cm, 60 cm, 90 cm, and 120 cm at shady and sunny slope sites, respectively. The soil water content and soil temperature were monitored continuously using the Trime and PICO32 sensors, which were installed at ten soil depths, including 5 cm, 10 cm, 20 cm, 40 cm, 80 cm, 100 cm, 120 cm, 140 cm, 160 cm and 180 cm. This dataset can support the long-term investigation of ecohydrological processes in typical catchment and also support the validation of hydrology models.
Li Xiaoyan
1) Data content: CT scan dataset of vegetation-soil-rock three-dimensional spatial structure of typical watersheds in Qilian Mountains, the data includes the volume density of moss layers at different depths, soil macroporosity and soil gravel volume density data in typical watersheds of Qilian Mountains; 2) Data Source and processing method: The moss layer and the undisturbed soil column with a depth of 30 cm under the moss cover were collected in a typical small watershed of the Qilian Mountains, and the moss layer and the undisturbed soil column were scanned with an industrial X-ray three-dimensional microscope; 3) Data quality description: The resolution of moss layer is 40 μm, and the resolution of undisturbed soil column is 68 μm; 4) Data application results and prospects: CT scan data set of vegetation-soil-rock three-dimensional spatial structure of typical small watersheds in Qilian Mountains is suitable for ecological restoration, water resources management and utilization in Qilian Mountains. It is of great significance and can provide basic data and theoretical support for elaborating the water conservation function and mechanism of the Qilian Mountains.
HU Xia
This data is the annual average runoff data from 1495 to 2018 of Khorog Hydrometric Station of gunte River, a tributary of Amu Darya River, reconstructed based on tree ring data. The data obtained from the tree ring hydrology research carried out by the Urumqi desert Meteorology Institute of the China Meteorological Administration and the Institute of water issues, hydropower and ecology of the National Academy of Sciences of Tajikistan can be used for scientific research such as water resources assessment and water conservancy projects in mountainous areas of Central Asia.
SHANG Huaming
The runoff plot is located in Shigatse, the Tibetan Plateau. The area had a serious soil erosion and large areas of low cover vegetation. Therefore, the runoff plot was constructed to monitor the soil erosion. The runoff plot had a length of 10 m, width of 5 m and a slope of 30°。 The vegetation coverage is low. The fully automatic runoff and sediment instrument was used to measured the runoff and sediment process. The temporal resolution varies with runoff process and had a high resolution when the water level changed rapidly. The measured results can provide the data support for the soil erosion in the Tibetan Plateau.
FU Suhua
This dataset contains daily 0.05°×0.05° land surface soil moisture products in Qilian Mountain Area in 2021. The dataset was produced by utilizing the optimized wavelet-coupled-RF downscaling model (RF-OWCM) to downscale the SMAP L3 Radiometer Global Daily 36 km EASE-Grid Soil Moisture (SMAP L3, V8). The auxiliary datasets participating in the downscaling model include the MUltiscale Satellite remotE Sensing (MUSES) LAI/FVC product, the daily 1-km all-weather land surface temperature dataset for the Chinese landmass and its surrounding areas (TRIMS LST-TP;) and Lat/Lon information.
CHAI Linna, ZHU Zhongli, LIU Shaomin
This dataset contains the ground surface water (including liquid water, glacier and perennial snow) distribution in Qilian Mountain Area in 2021. The dataset was produced based on classical Normalized Difference Water Index (NDWI) extraction criterion and manual editing. Landsat images collected in 2021 were used as basic data for water index extraction. Sentinel-2 images and Google images were employed as reference data for adjusting the extraction threshold. The dataset was stored in SHP format and attached with the attributions of coordinates and water area. Consisting of 1 season, the dataset has a temporal resolution of 1 year and a spatial resolution of 30 meters. The accuracy is about 1 pixel (±30 meter). The dataset directly reflects the distribution of water bodies within the Qilian Mountain in 2021, and can be used for quantitative estimation of water resource.
Li Jia Li Jia LI Jia LI Jia
This dataset provides the monitoring data of runoff, precipitation and temperature of the Duodigou Runoff Experimental Station located in the northern suburbs of Lhasa city. Among the dataset, there are two runoff monitoring stations, which provide discharge data from June to December 2019, with a data step of 10 minutes. There are five precipitation monitoring stations, which provide precipitation data from 2018 to 2021, with a data step of 1 day. There are eight air temperature monitoring stations, which provide air temperature data from 2018 to 2021 in 30 minute steps. The discharge, the precipitation and the temperature data are the measured values. The dataset can provide data support for the study of hydrological and meteorological processes in the Tibet Plateau.
LIU Jintao
The evapotranspiration (ET) is an important variable connecting land energy balance, water cycle and carbon cycle. Accurate monitoring and estimations of ET are essential not only for water resources management but also for simulating regional, global climate, and hydrological cycles. Remote sensing technology is an effective method to monitor ET. At present, a variety of ET remote sensing products have been produced and released. However, in the process of validation, there is a problem of spatial scale mismatch between ET remote sensing estimation value and station observation value, especially on heterogeneous surface. Therefore, it is very important to obtain the ground truth ET values at the satellite pixel scale by upscaling method on heterogeneous surface. In this study, using the station observation data and multi-source remote sensing information, the ET observed at a single ground station is upscaled to the satellite pixel scale, and the ground truth ET values at the satellite pixel scale in Heihe River Basin is obtained. Based on the ET data observed by the eddy covariance (EC) at 15 stations (3 superstations and 12 ordinary stations) in the Heihe integrated observatory network, combined with the fused high-resolution remote sensing data (surface temperature, vegetation index, net radiation, etc.) and atmospheric reanalysis data, the upscaling is carried out to obtain the ground truth ET at the satellite pixel scale. The distribution diagram is shown in Figure 1. Specifically, firstly, the spatial heterogeneity of the spatial heterogeneity of the land surface hydrothermal conditions was evaluated; Secondly, nine upscaling methods (the integrated Priestley-Taylor equation method, the Penman-Monteith equation combined with EnKF method, the Penman-Monteith equation combined with SCE_UA method, EC observation value, artificial neural network, Bayesian linear regression, deep belief network, Gaussian process regression, and random fores and directly taking the EC observation value as the ground truth ET) were compared and analyzed through direct validation and cross-validation; Finally, a comprehensive method (directly using the EC observation value on the homogeneous underlying surface; using the Gaussian process regression method for upscaling on the moderately heterogeneous underlying surface and highly heterogeneous underlying surface) was optimized to obtain the groud truth ET at the satellite pixel scale at 15 typical underlying surfaces in Heihe River Basin (2010-2016, spatial resolution of 1km). The results showed that the ground truth ET at the satellite pixel scale is relatively reliable. Compared with the pixel scale reference value (LAS observation value), the MAPE of the ground turth ET at the satellite pixel scale at the three superstations are 1.57%, 3.23% and 4.59% respectively, which can meet the needs of the validation of ET remote sensing products. For all site information and data processing, please refer to Liu et al. (2018), and for upscaling methods, please refer to Li et al. (2021).
LIU Shaomin, LI Xiang , XU Ziwei
This data is the hydrological data of the Khujand Hydrological Station in the middle reaches of the Syr Darya. The station is jointly constructed by the Urumqi Desert Meteorological Institute of the China Meteorological Administration, the Institute of Water Issues, Hydropower and Ecology of the National Academy of Sciences of Tajikistan, and the Tajikistan Hydrological and Meteorological Bureau. This data can be used for scientific research such as water resource assessment in Central Asia and services such as water conservancy projects. Data period: December 5, 2020 to September 11, 2021. Data elements: hourly flow velocity (m/s), hourly water level (m) and hourly rainfall (m) Site location: 40°17′38″N, 69°40′18″E, 320m 1. 300W-QX river velocity and water level observation instrument (1) Flow rate parameters: 1 Power supply voltage 12 (9~27) V(DC) 2 Working current 120 (110~135) mA 3 Working temperature (-40 ~85) °C 4 Measuring range (0.15 ~20) m/s 5 Measurement accuracy ±0.02m/s 6 Resolution 1mm 7 Detection distance 0.1~50 m 8 Installation height 0.15~ 25 m 9 sampling frequency 20sps (2) Water level parameters: 1 Measuring range 0.5~20 m 2 Measurement accuracy ±3 mm 3 Resolution 1 mm 4 Repeatability ±1mm 2. SL3-1 tipping bucket rain sensor 1 Water bearing diameter ф200mm 2 Measure the precipitation intensity within 4mm/min 3 measure the minimum division of 0.1mm precipitation 4 Maximum allowable error ±4%mm 3. Frequency of flow rate and observation instrument data acquisition: The sensor measures the flow rate and water level data every 5S 4. Hourly average flow rate calculation: The hourly average flow rate and water level data are calculated from the average of all flow rate and water level data measured every 5S within one hour
HUO Wen
This data is the hydrological data of the Kaffinigan Hydrological Station, the upper tributary of the Amu Darya. The station is jointly constructed by the Urumqi Desert Meteorological Institute of the China Meteorological Administration, the Institute of Water Issues, Hydropower and Ecology of the National Academy of Sciences of Tajikistan, and the Tajikistan Hydrological and Meteorological Bureau. This data can be used for scientific research such as water resource assessment in Central Asia and services such as water conservancy projects. Data period: December 4, 2020 to September 4, 2021. Data elements: hourly flow velocity (m/s), hourly water level (m) and hourly rainfall (m) Site location: 37°36′01″N, 68°08′01″E, 420m 1. 300W-QX river velocity and water level observation instrument (1) Flow rate parameters: 1 Power supply voltage 12 (9~27) V(DC) 2 Working current 120 (110~135) mA 3 Working temperature (-40 ~85) °C 4 Measuring range (0.15 ~20) m/s 5 Measurement accuracy ±0.02m/s 6 Resolution 1mm 7 Detection distance 0.1~50 m 8 Installation height 0.15~ 25 m 9 sampling frequency 20sps (2) Water level parameters: 1 Measuring range 0.5~20 m 2 Measurement accuracy ±3 mm 3 Resolution 1 mm 4 Repeatability ±1mm 2. SL3-1 tipping bucket rain sensor 1 Water bearing diameter ф200mm 2 Measure the precipitation intensity within 4mm/min 3 measure the minimum division of 0.1mm precipitation 4 Maximum allowable error ±4%mm 3. Frequency of flow rate and observation instrument data acquisition: The sensor measures the flow rate and water level data every 5S 4. Hourly average flow rate calculation: The hourly average flow rate and water level data are calculated from the average of all flow rate and water level data measured every 5S within one hour
HUO Wen
This data set collates and collects the measured and investigated maximum 24h rainfall point data along the Sichuan Tibet railway and its surrounding areas. It contains field data of watershed kid, station, province, X coordinate, y coordinate, rain, date, etc. A total of 43 records. Data source: Atlas of rainstorm statistical parameters in China (2006 Edition). Processing method: manually digitize the measured and investigated maximum 24h rainfall point data of China's rainstorm statistical parameter Atlas (2006 Edition) in the areas along and around the Sichuan Tibet railway. The data set also includes the maximum 24h precipitation values (1950s-2010s) of all sub watershed units in the assessment area along the Sichuan Tibet railway, which are calculated according to the frequency of the annual maximum 24h precipitation sequence in the assessment area. In the process of processing, the operators are required to strictly abide by the operation specifications, and a special person is responsible for the quality review. The data integrity, logical consistency, position accuracy, attribute accuracy, edge connection accuracy and current situation all meet the requirements of relevant technical regulations and standards formulated by the State Bureau of Surveying and mapping, and the quality is excellent and reliable.
WANG Zhonggen
PML-V2(China) terrestrial evapotranspiration and total primary productivity dataset, including five elements: gross primary product (GPP), vegetation transpiration (Ec), soil evaporation (Es), vaporization of intercepted rainfall (Ei) and water body, ice and snow evaporation (ET_water). The dataset has a spatial-temporal resolution of daily and 500-meter from Feb.26, 2000 to Dec.31, 2020. Compared with the global version, the simulation accuracy of the PML-V2(China) product has been greatly improved, which has the following improvements and innovations: I. Compared with the 8-day temporal resolution of the global version, the new product is daily; II. The observation data are from 26 eddy flux stations in China, which are with 9 underlying surface types including deserts with sparse vegetation, and used for the parameter calibration of the model (there are only eight stations located in China for calibrating the global PML-V2, covering only five vegetation types); III. China meteorological forcing dataset for 2000-2018 and the global land surface data assimilation system GLDAS-2.1 meteorological dataset with bias correction for 2019-2020 are used to replace the original 0.25 ° GLDAS meteorological inputs; IV. The ERA5-Land as the input surface temperature instead of air temperature to calculate the outgoing longwave radiation; and V. Taking the MODIS leaf area index by the improved Whittaker filter as the model input, the new product provides new insights into monitoring crop water consumption and reveals the characteristics of the planting system. Please note that the dataset does not include the South China Sea.
ZHANG Yongqiang, HE Shaoyang
This dataset contains daily 0.05°×0.05° land surface soil moisture products in Qilian Mountain Area in 2020. The dataset was produced by utilizing the optimized wavelet-coupled-RF downscaling model (RF-OWCM) to downscale the SMAP L3 Radiometer Global Daily 36 km EASE-Grid Soil Moisture (SMAP L3, V8). The auxiliary datasets participating in the downscaling model include GLASS Albedo, MUSES LAI/FVC, Daily 1-km all-weather land surface temperature dataset for Western China (TRIMS LST-TP; 2000-2021) V2 and Lat/Lon information.
CHAI Linna, ZHU Zhongli, LIU Shaomin
This dataset contains in-situ lake level observations at Lumajiangdong Co, Memar Co，Camelot Lake and Jieze Caka on the western Tibetan Plateau. The lake water level was monitored by HOBO water level logger (U20-001-01) or Solist water level logger, which was installed on the lake shore. Lake level data was then calibrated by using the barometer installed near the lake. Then the real water level changes were obtained. The accuracy was less than 0.5 cm. The items of this dataset are as follows: Daily lake level changes at Lumajiangdong Co from 2016 to 2021; Daily lake level changes at Memar Co from 2017 to 2019 and from 2020 to 2021; Daily lake level changes at Luotuo Lake from 2019 to 2020. Daily lake level changes at Jieze Caka Lake from 2019 to 2020. Water level, unit: m.
LEI Yanbin
Asian, and is divided into 1100 sub-basins for distributed hydrological modelling. The integrated water system model (HEQM) is improved to simulate the freezing and thawing processes of snow cover and glacier in this region. The historical daily weather inputs (i.e., precipitation and temperature) with high spatial resolution (0.45 degree) are obtained using the image fusion of NECP and ECMWF based on compressed sensing in the domain of Fourier coefficients, and the long-term annual runoff observations from 1940 to 2000 at 22 stations were used to implement of HEQM calibration and validation. Furthermore, the future weather inputs are rebuilt using the median of daily climate outputs of five GCMs in the Inter-Sectoral Impact Model Intercomparison Project (ISI-MIP) and then drive the well-calibrated HEQM to project the development and utilization potentials of agricultural water resources in the future. The data sets includes three time periods of 2000s (2001-2005), 2010s (2006-2010) and 2015s (2011-2015) for the historical period, and two periods of 2040s (2041-2070) and 2070s (2071-2099) for the future period in the RCP4.5 and RCP8.5 with a spatial resolution of 0.5°*0.5°. It is expected to provide basic data support for distributed water cycle simulation, water supply and demand, development and utilization analysis in the Central Asian.
ZHANG Yongyong, LIU Yu , YANG Peng
This data is the runoff and evapotranspiration generated by the precipitation in the growing season of the upper reaches of Heihe River from 1992 to 2015. Temporal resolution: year (growingseason), spatial resolution: 0.00833°. The data include precipitation (mm), evapotranspiration (mm), runoff (mm) and soil water content (m3 / m3). The data are obtained by using meteorological, soil and vegetation parameters based on Eagleson eco hydrological model. The simulated rainfall runoff is verified by using the observed runoff data in the growing season of 6 sub basins in the upper reaches of Heihe River (Heihe main stream, Babao River, yeniugou, Liyuan River, Wafangcheng and Hongshui River). The variation range of correlation coefficient (R) is 0.53-0.74, RMSE is 32.46-233.18 mm, and the relative error range is -0.66-0.0005; The difference between simulated evapotranspiration and gleam et is − 115.36 mm to 44.1 mm. The simulation results can provide some reference for hydrological simulation in the upper reaches of Heihe River.
ZHANG Baoqing
This dataset contains 10 years (2010-2019) global daily surface soil moisture . The resolution is 36 km , the projection is EASE-Grid2, and the data unit is m3 / m3. This dataset adopts the soil moisture neural network retrieval algorithm developed by Yao et al. (2017，2021). This study transfers the merits of SMAP to FY-3B/MWRI through using an Artificial Neural Network (ANN) in which SMAP standard SSM products serve as training targets with FY-3B/MWRI brightness temperature (TB) as input. Finally, long term soil moisture data are output. The accuracy is about 5% volumetric water content，which is comparable with that of SMAP. (evaluation accuracy of 14 dense ground network globally.)
YAO Panpan, LU Hui, ZHAO Tianjie, WU Shengli , SHI Jiancheng
A long-term (1980-2017) land evaporation (E) product with a spatial resolution of 0.25 degree. This is a merged product from three model-based E products using the Reliability Ensemble Averaging (REA) method which minimizes errors. These include the fifth-generation ECMWF Re-Analysis (ERA5), the second Modern-Era Retrospective analysis for Research and Applications (MERRA2), and the Global Land Data Assimilation System (GLDAS). To facilitate user-friendly access and download the dataset is stored individually for each year in a separate file. These files contain daily and monthly mean data (e.g., REA_1980_day.nc and REA_1980_mon.nc). The dataset is stored in NetCDF format, containing the variable E, representing land evaporation, produced in millimeters (mm) as a unit. There are three dimensions included in the dataset: longitude, latitude, and time, with the longitude ranging from -179.875E to 179.875E, the latitude from -59.875N to 89.875N. Complete time coverage is from January 1, 1980, to December 31, 2017.
LU Jiao, WANG Guojie, CHEN Tiexi, LI Shijie, HAGAN Daniel, KATTEL Giri, PENG Jian, JIANG Tong, SU Buda
This dataset is the water balance dataset in the Yellow River source region and Qilian Mountains in the future 50 years (runoff, precipitation, evapotranspiration, soil liquid water content). It is simulated by the Geomorphology-Based Ecohydrological Model (GBEHM). The variables in the dataset include monthly runoff, monthly precipitation, monthly evapotranspiration, the monthly average 5cm soil liquid water content and the monthly average 50cm soil liquid water content. The temporal range is 2020-2070 and the spatial resolution is 1 km. The input data of the model include meteorological forcings, vegetation, soil and land use data, and the meteorological forcings are obtained from the ensemble mean of 38 CMIP6 models under SSP2-4.5 scenario. The simulation results can reflect the spatio-temporal changes of the hydrological variables in the Yellow River source region and Qilian Mountains. The dataset can be further used for researches into the eco-hydrological processes in the Yellow River source region and Qilian Mountains, and help provide a scientific basis for the optimal allocation of " mountains, rivers, forests, farmlands, lakes and grasslands " system.
WANG Taihua, YANG Dawen
This dataset is the water balance dataset in the Yellow River source region and Qilian Mountains in the past 40 years (runoff, precipitation, evapotranspiration, soil liquid water content). It is simulated by the Geomorphology-Based Ecohydrological Model (GBEHM). The variables in the dataset include monthly runoff, monthly precipitation, monthly evapotranspiration, the monthly average 5cm soil liquid water content and the monthly average 50cm soil liquid water content. The temporal range is 1980-2019 and the spatial resolution is 1 km. The input data of the model include meteorological forcings, vegetation, soil and land use data. The simulation results can reflect the spatio-temporal changes of the hydrological variables in the Yellow River source region and Qilian Mountains. The dataset can be further used for researches into the eco-hydrological processes in the Yellow River source region and Qilian Mountains, and help provide a scientific basis for the optimal allocation of " mountains, rivers, forests, farmlands, lakes and grasslands " system.
WANG Taihua, YANG Dawen
This dataset is an 8-year (2011-2018) global spatiotemporally consistent surface soil moisture dataset with a 25km spatial grid resolution and daily temporal step in unit of cm3/cm3. This dataset is developed by applying a linear weight fusion algorithm based on the Triple Collocation Analysis (TCA) to merge the five soil moisture data products, i.e., SMOS, ASCAT, FY3B, CCI and SMAP in two steps. The first step is to fuse the SMOS, ASCAT and FY3B soil moisture products from 2011 to 2018. The second step is to refuse the merged soil moisture product in the first step, CCI and SMAP products from 2015 to 2018, and to obtain the finally merged soil moisture product from 2011 to 2018. In addition, the measured soil moisture data from seven ground observation networks around the world are used to evaluate and analyze the merged soil moisture product. The fused soil moisture product has the global spatial coverage ratio of more than 80%. With rhe minimum RMSE (root mean square error) of 0.036 cm3/cm3.
JIA Li , XIE Qiuxia, XIE Qiuxia, XIE Qiuxia, XIE Qiuxia, XIE Qiuxia, XIE Qiuxia, XIE Qiuxia, XIE Qiuxia, XIE Qiuxia, HU Guangcheng
1. Glacial lake data sets (1960s−2020) This data set contains glacial lake data for the 1960s, 2016, 2017, 2018, 2019, and 2020, mapped from Korona KH-4, Sentinel-2, and Sentinel-1 imagery. 2. Potential Outburst Flood Hazard level of Bhutanese glacial lakes This data contains the Potential Outburst Flood Hazard level of Bhutanese glacial lakes with an area greater than 0.05 km2 (n=278). The value for each hazard assessment criteria is also provided in the data attributes.
RINZIN Sonam, ZHANG Guoqing
The data include four types: water levels of 244 lakes extracted in CryoSat-2 L1B Baseline D (2010-2020); water levels of 356 lakes extracted in ICESat-2 ATL13 (2018-2020); water levels of 125 lakes extracted in Sentinel-3A SRAL L2 (2016- 2020); water levels in 120 lakes extracted from Sentinel-3B SRAL L2 (2018-2020). Data include date, decimal date, water level, standard deviation, and geographic location of each lake. Please see the paper for detailed data processing procedures.
XU Fenglin, ZHANG Guoqing
This data set is the version 2 of "High temporal and spatial resolution precipitation data of Upper Brahmaputra River Basin (1981-2016) ", with additional data from 2017 to 2019. This data set describes the temporal and spatial distribution of precipitation in the Upper Brahmaputra River Basin. We integrate (CMA, GLDAS, ITP-Forcing, MERRA2, TRMM) five sets of reanalysis precipitation products and satellite precipitation products, and combine the observation precipitation of 9 national meteorological stations from China Meteorological Administration (CMA) and 166 rain gauges of the Ministry of Water Resources (MWR) in the basin. The time range is 1981-2019, the time resolution is 3 hours, the spatial resolution is 5 km, and the unit is mm/h. The data will provide better data support for the study of Upper Brahmaputra River Basin, and can be used to study the response of hydrological process to climate change. Please refer to the instruction document uploaded with the data for specific usage information.
WANG Yuanwei, WANG Lei, LI Xiuping, ZHOU Jing
The SZIsnow dataset was calculated based on systematic physical fields from the Global Land Data Assimilation System version 2 (GLDAS-2) with the Noah land surface model. This SZIsnow dataset considers different physical water-energy processes, especially snow processes. The evaluation shows the dataset is capable of investigating different types of droughts across different timescales. The assessment also indicates that the dataset has an adequate performance to capture droughts across different spatial scales. The consideration of snow processes improved the capability of SZIsnow, and the improvement is evident over snow-covered areas (e.g., Arctic region) and high-altitude areas (e.g., Tibet Plateau). Moreover, the analysis also implies that SZIsnow dataset is able to well capture the large-scale drought events across the world. This drought dataset has high application potential for monitoring, assessing, and supplying information of drought, and also can serve as a valuable resource for drought studies.
WU Pute, TIAN Lei, ZHANG Baoqing
Contact Support
Northwest Institute of Eco-Environment and Resources, CAS
0931-4967287
poles@itpcas.ac.cn
Links
National Tibetan Plateau Data CenterFollow Us
A Big Earth Data Platform for Three Poles © 2018-2020 No.05000491 | All Rights Reserved
｜ 
No.11010502040845
Tech Support: westdc.cn
